The IC has been used extensively as part of a USB UART TTL 3.3v cable which is marketed by a Chinese company called Sinforcon. The FT230X IC has been used in the cable and it is USB 2.0, USB1.0 compatible. It also has an integrated 2048 byte EEPROM and is sold as a USB UART TTL cable supporting TTL 3.3v or TTL 5v. A virtual COM port driver needs to be installed onto the PC to use Radio Control Program ARCP-990, ARCP-890, ARCP-590G, or ARCP-590 with the USB cable.: The ARUA-10 will not be used while USB Audio function of the transceiver is in use in data communications such as JT65, FT8, or KENWOOD NETWORK COMMAND SYSTEM remote operations. If the transceiver is connected to a PC using a USB cable, ensure that the connection is directly in place. ARCP-990 may not behave properly if a connection is in place through a USB hub. Download and install the virtual COM port driver to make a USB connection possible for command communications via a USB connector.

1. Kenwood Usb Devices Driver Download Free
2. Kenwood USB Devices Driver Download
3. Kenwood Usb Devices Driver Download Windows 10

The FT230X is a compact bridge to basic UART interfaces with low power consumption (8mA) and operating up to 3M Baud. The IC has been used extensively as part of a USB UART TTL 3.3v cable which is marketed by a Chinese company called Sinforcon. The FT230X IC has been used in the cable and it is USB 2.0, USB1.0 compatible. It also has an integrated 2048 byte EEPROM and is sold as a USB UART TTL cable supporting TTL 3.3v or TTL 5v.

FT230X – Full Speed USB to Basic UART

Kenwood Usb Devices Driver Download Free

The baud rate as advertised for the cable is with a 256kbps baud rate, 28AWG *4 core or 6 core and also supports TX, RX, CTS, RTS, VCC and GND. For most operating systems there are only two types of drivers available. This being the Virtual COM Port (VCP) drivers and direct (D2XX) drivers. The VCP driver emulates a standard PC serial port such that the USB device may be communicated with as a standard RS232 device. The IC has been typical used in USB Wireless Modems as well as USB to RS232/RS422/RS485 converters like the one that has been explained above. The FT230X IC has a number of uses and hardware features such as what has been listed below.

• It can be used as a single chip USB to asynchronous serial data transfer interface such as USB cable to serial cable connections;
• USB protocols are handled on the chip so there is no need for any specific firmware programming;
• The IC comes with a 2048 byte EEPROM which can be used for device descriptors;
• The EEPROM can also be used for CBUS I/O configuration;
• There is integrated clock generation (6MHz, 12MHz, 24MHz, and 48MHz);
• The IC does not need an external clock;
• The baud rates of 300 baud to 3 Mbaud is possible;
• The 512 byte receive and transmit buffers makes data throughput high;
• The CBUS I/O pins is configurable;
• Faster charging batteries as it has a battery charger detector for USB;
• There are also configurations for bus powered, self powered and a high-power bus;
• The IC also comes with a UART signal inversion option;
• The current of 8mA (typical) and USB suspend current of 125uA (typical) current.

These are some of the features.

With the UART driver for the IC you do not need to write a USB driver for the product using the IC. This helps to lower production cost as the IC is used it a variety of products. The IC is also used in an number of evaluation and demonstration boards and kits. There is also a number of other uses such as the DB9 to 2.5mm stereo jack adapter cable which is used on products for Kenwood.

Incoming Search Terms:

Kenwood USB Devices Driver Download

Related Posts

• Common UART problems (1.000)
• Silicon Labs UART Drivers (1.000)
• FT231X – Full Speed USB to Full UART (1.000)
• UART Drivers (1.000)
• ASUS VivoBook 17 F712FA UART Driver Win 10 64-bit (1.000)

Kenwood Usb Devices Driver Download Windows 10

KENWOOD USB Audio Controller ARUA-10 Version 4.00 Last updated : August 30, 2018 About this software This is the software to be used to connect a TS-990S, a TS-890S, a TS-590SG, or a TS-590S transceiver and a PC by a USB cable and make it possible to use a speaker and a microphone on your PC instead of those on the transceiver. Using this software coupled with ARCP-990, ARCP-890, ARCP-590G, or ARCP-590, simply connecting a PC to a transceiver using a USB cable makes it possible to control the transceiver from the PC. Note: A virtual COM port driver needs to be installed onto the PC to use Radio Control Program ARCP-990, ARCP-890, ARCP-590G, or ARCP-590 with the USB cable. The ARUA-10 will not be used while USB Audio function of the transceiver is in use in data communications such as JT65, FT8, or KENWOOD NETWORK COMMAND SYSTEM remote operations. Please refer to the following manuals for details. TS-990S USB Audio Setting Manual : (580KB PDF). TS-890S USB Audio Setting Manual : (659KB PDF). TS-590SG USB Audio Setting Manual : (506KB PDF). TS-590S USB Audio Setting Manual : (525KB PDF). Operating Environment 1. Operating System (OS) Windows® 7 (SP1 or later) (32-bit or 64-bit) Windows® 8.1 (RTM or later) (32-bit or 64-bit) Windows® 10 (Version 1703 (OS Build 15063.0) or later) (32-bit or 64-bit) Note: This software is designed to run on the above operating systems. Applicable operating systems are subject to change without notice due to the end of the technical support by Microsoft Corporation or change of the product specifications. 2. Processor Faster than the recommended CPU for each OS. 3. System Memory (RAM) Larger than the recommended System Memory for each OS. 4. Free Hard Drive Space 100 MB or more of free hard drive space. 5. Runtime Microsoft .NET Framework 3.5 (includes .NET 2.0 and 3.0). 6. Peripheral Devices A display with resolutions higher than XGA (1024 x 768). A keyboard and a mouse, or other pointing devices. USB 2.0 interface. * If the transceiver is connected to a PC using a USB cable, ensure that the connection is directly in place. ARUA-10 may not behave properly if a connection is in place through a USB hub.. * Download and install the virtual COM port driver to make a USB connection possible for command communications via a USB connector. Sound function. A speaker and a microphone.(Or a headset.) Usage Notes Users are prohibited to assign, rent, lease, redistribute, or resell the software. Users are prohibited to revise, change, translate, merge, de-compile, or reverse engineer the software. JVC KENWOOD does not warrant that quality and functions of this software comply with each user's purpose of use of this software, and unless specifically described in this document, JVC KENWOOD shall be free from any responsibilities to any defects and indemnities to any damages or losses. Selection and installation of this software shall be made by the User's designation. The User shall take full responsibilities for the use and effects of this Software. JVC KENWOOD Corporation shall be free from any responsibilities for any incidental losses or damages, such as missing communications or a calling opportunity caused by a failure or performance error of this Software. JVC KENWOOD shall own all copyrights and other intellectual properties for the software and all manuals and documents attached to the software. The user shall be allowed to use, not to resell, the software by obtaining a license from JVC KENWOOD. While the media in which the software is stored is possessed by the user, the ownership for the software itself shall be reserved for JVC KENWOOD. Installing the ARUA-10 Extract the downloaded file 'ARUA10_400.zip' into a designated folder. In the designated folder, a folder labeled 'ARUA10_400' will be created. Execute the 'Setup.exe' in the folder labeled 'ARUA10_400', and follow the instructions that appear on the display to install ARUA-10. Note: Administrator privileges are required when installing the software. To update ARUA-10, execute the same procedure as used for installation, and follow the instructions that appear on the display to install the software. The latest update is written and installed over the currently installed program. Uninstalling the ARUA-10 Select 'ARUA-10' in 'Control Panel - Programs and Features' for Windows® 7/8.1, or in 'Settings - Apps & features' for Windows® 10, and follow the instructions that appear on the display to uninstall the software. Or double-click 'Setup.exe', and follow the instructions that appear on the display to uninstall the software. Administrative privileges are required to uninstall ARUA-10. Always exit ARUA-10 before uninstalling the software.. If you agree with the details listed above, click the following link to download the ARUA-10 software. (The latest version includes all previous updates.) ARUA-10 Ver.4.00 :ARUA10_400.zip 6.70MB download Update History Ver.4.00 (August 30, 2018) Enables to use with the TS-890S. Adds Windows® 10 compatibility. Ver.3.00 (October 31, 2014) Enables to use with the TS-590SG. Adds Windows® 8.1 compatibility. Ver.2.01 (July 12, 2013) Adds Windows® 8 compatibility. Ver.2.00 (February 28, 2011) Enables to use with the TS-990S. Ver.1.00 (October 15, 2010) First Release. Microsoft®, Windows®, and Windows logo are registered trademarks of Microsoft Corporation in the United States and/or other countries. .NET Framework is a trademark or a registered trademark of Microsoft Corporation in the United States and/or other countries.